CategoryCollings59511

Freenas ahci timeout on slot

By Mark Zuckerberg

The timeout happens on different drives, not always the same. Also it does not care which drive I call smartctl on. Does someone have an idea what I could try to avoid these hang and timeouts? My system is using FreeNAS 9.3-BETA 2014-11-22 on a ASRock C2550D4I, SATA cables and power supply have already been replaced.

Pfsense/FreeNAS Build Questions - Networking Hardware Apr 15, 2016 · Pfsense/FreeNAS Build Questions. Networking. Networking Hardware. Andrewskaterrr April 10, 2016, Can the 4 SCU SATAs be used in conjunction with the AHCI SATAs? ie: a ZFS2 pool and have 3 drives on AHCI controller and 2 drives on the SCU. ... For video transcoding with plex it would be 1 movie at a time, and video encoding would be done at ... SATA DOM Boot Device RAID | FreeNAS Community Feb 26, 2016 · Thanks for the reply. The install went fine after deleting the RAID, and switching the onboard controller back to AHCI. Just for my clarification, what exactly does selecting both during installation do? Is FreeNAS managing a mirror or something similar? Just want to understand exactly how this changes an install.

[SOLVED] FREENAS - can't access data on vol1 any... -…

FreeNAS 9.10 on VMware ESXi 6.0 Guide | b3n.org This is a guide which will install FreeNAS 9.10 under VMware ESXi and then using ZFS share the storage back to VMware. This is roughly based on Napp-It’s All-In-One design, except that it uses FreeNAS instead of OminOS.

Forum discussion: I've been using SSDs for probably 7 or 8 years now. My first was a Crucial M4, still going strong. I must have 10-12 in various forms of service. I just had my first failure.

freenas kernel: cpu0: on acpi0 Sep 17 22:21:38 freenas kernel: ACPI Warning: Incorrect checksum in table [OEMB] - 0x07, should be 0xFA21:38 freenas kernel: isa0: on isab0 Sep 17 22:21:38 freenas kernel: ahci0: port 0xec00-0xec07... How to restart web ui on freenas - Server Fault I've come across a bug with freenas where the web ui (lighthttpd) can freeze up and render the service to hang. Is there an easy way to restart this service via a terminal?Current versions of FreeNAS use nginx and the Django framework. They can be restarted as follows Настройка жёстких дисков в zfs пул на nas4free, вариант… NB Это вариант для nas4free 10. В более ранних версиях на базе 9.x настройка ZFS чуть другая Мы подключили новый диск и включили nas4free. Создадим на нём zfs пул через вебгуй. Текст предназначен для новичков. Гораздо подробнее, чем привыкли постоянные читатели - не... 23. Command Line Utilities — FreeNAS User Guide 9.3 Table… Several command line utilities which are provided with FreeNAS® are demonstrated in this section. The following utilities can be used for benchmarking and performanceIperf is a utility for measuring maximum TCP and UDP bandwidth performance. It can be used to chart network throughput over time.

AHCI Timeout and Reboot problem - OPNsense Forum - Index

As I see there is no DIPM power saving enabled by default in loader.conf so I think power saving is regulated by other features. What I would like to say is if somebody has CAM errors on an AMD SB7x chipset should think about explicitly disabling AHCI power saving as I suggested which may take you 0.8W but you get a stable system for this small price. FreeNAS 8.0.2: AHCI Timeouts? | [H]ard|Forum About 10 minutes into it, I start getting "ahcichX: Timeout on slot NN port 0" where X ranges from 0-3 for all four disks. The list of related errors just keeps going. I have looked over at the FreeNAS forums and the problem has been reported by others using different hardware. Unfortunately, those forums aren't very active.